test

(redirected from thermal test)
Also found in: Dictionary, Medical, Legal, Financial, Encyclopedia.
Graphic Thesaurus  🔍
Display ON
Animation ON
Legend
Synonym
Antonym
Related
  • all
  • verb
  • noun
  • adj
  • phrase

Synonyms for test

check

Synonyms

examine

Synonyms

  • examine
  • put someone to the test
  • put someone through their paces

challenge

Synonyms

put something to the test

Synonyms

Synonyms for test

a procedure that ascertains effectiveness, value, proper function, or other quality

an operation employed to resolve an uncertainty

a set of questions or exercises designed to determine knowledge or skill

a means by which individuals are compared and judged

constituting a tentative model for future experiment or development

to subject to a procedure that ascertains effectiveness, value, proper function, or other quality

to subject to a test of knowledge or skill

to engage in experiments

Synonyms

Synonyms for test

any standardized procedure for measuring sensitivity or memory or intelligence or aptitude or personality etc

the act of undergoing testing

a hard outer covering as of some amoebas and sea urchins

put to the test, as for its quality, or give experimental use to

test or examine for the presence of disease or infection

Synonyms

Related Words

examine someone's knowledge of something

Synonyms

Related Words

show a certain characteristic when tested

Related Words

achieve a certain score or rating on a test

Related Words

determine the presence or properties of (a substance)

undergo a test

Related Words

References in periodicals archive ?
For this reason, instead of using as reference temperatures the values measured during thermal tests, the following procedure has been employed.
Furthermore, some products were not operational, as some necessary hardware was removed for thermal test requirements.
The thermal test chip in the SCM was 18.5 x 18.6 mm in size and the powered area was 3 [cm.sup.2].
TELECOMWORLDWIRE-27 January 2009-Telkonet selected to provide PLC technology for Sandia National Solar Thermal Test Facility(C)1994-2009 M2 COMMUNICATIONS LTD http://www.m2.com
To evaluate and validate the performance of the thermal test for the diagnosis of leprosy, a receiver operating characteristic (ROC) curve was used, which shows a graphic representation of the sensitivity and specificity of the test and allows the selection of a more appropriate cut-off point as determined by the definitive diagnosis.
We were able to produce a resistor thermal test vehicle design 10 months ago.
Therefore, it is crucial to have a temperature-mapping tool that reliably collects thermal data across the area of a standard wafer without itself perturbing the thermal test environment.
In the clips, casks were subjected to a full-scale drop from nine meters onto an unyielding target, a one-meter puncture test onto a steel pin welded to an unyielding surface, a thermal test in which the cask was engulfed in a 1,475[degrees]F fire for 30 minutes, and a full-scale rail test in which the cask was smashed into a concrete block at 81 mph.
The thermal test capabilities developed for the Rosetta programme have been extended for subsequent programmes to enable testing to temperatures as low as -160[degree]C and rates of change of temperature as high as 30[degree]C/minute (load),70[degree]C/minute (air).
ATS has continued to expand in the COTS industry because of its expertise in resolving thermal challenges through its consulting services, cooling solutions, and thermal test instruments.
The samples were preconditioned at IRTS with IPC PCQR (2) assembly cycle standard of six simulated solder assembly cycles, then put on thermal test. Thirteen days and 2,000 cycles later, the FR-4 six-layer boards passed 2,000 cycles with less then two percent change in resistance.
Tyner and his colleagues at Sandia's National Solar Thermal Test Facility worked with industry from 1980 to 1987 to design and test three molten-salt-based thermal receivers capable of generating 5 megawatts of steam from concentrated solar energy.
It supports thermal test from -50[degrees]C to +250[degrees]C and can characterize the device power loss (conduction loss, switching loss, and driving loss) vs.
"Nobody has ever used a similar method and thermal test in order to obtain such mechanical properties.
The samples were preconditioned at IRTS with IPC PCQ[R.sup.2] assembly cycle standard of six simulated solder assembly cycles, then put on thermal test. Thirteen days and 2,000 cycles later, the FR-4 six-layer boards passed 2,000 cycles with less then two percent change in resistance.